Honeywell Thermostat CT2095 User Manual - Honeywell Thermostat Manual Download

Latest

Sunday, April 5, 2020

Honeywell Thermostat CT2095 User Manual

Honeywell/20 Programmable Thermostat OWNER’S GUIDE Weekday/Weekend (5-day/2-day) Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model CT2095 Place Bar Code Here 69- 1385 Welcome to the world of comfort and energy savings with your new Honeywell Programmable Thermostat. MERCURY NOTICE If this thermostat is replacing a thermo- Your new thermostat will automatically control stat that contains mercury in a sealed the temperature in your home, keeping you tube, do not place your old thermostat in comfortable while saving energy when the trash. Dispose of properly. programmed according to the instructions in this manual. Contact your local waste management authority for instructions regarding recy- Direct any questions concerning the application cling and the proper disposal of your old of this thermostat to Honeywell Consumer thermostat. If you have questions, call Services at 1-800-468-1502, Monday-Friday, Honeywell Customer Response Center 7:00 a.m.-5:30 p.m., Central time. at 1-800- 468-1502. MERCURY SWITCH Typical location of a mercury switch in a thermostat. M3701 2 69-1385 Contents Step 1. Prepare for Installation ..................................................................................................... 4 Step 2. Remove Old Thermostat ..................................................................................................6 Step 3. Install Batteries ................................................................................................................ 8 Step 4. Program Thermostat ........................................................................................................ 11 Step 5. Adjust Fan Operation Switch, As Required ...................................................................... 19 Step 6. Adjust System On-Time, °F/°C, As Required ................................................................... 19 Step 7. Mount Thermostat Mounting Plate ................................................................................... 21 Step 8. Wire Thermostat Terminals ..............................................................................................23 Step 9. Mount Thermostat ............................................................................................................ 27 Step 10. Check Thermostat Operation After Programming and Installing ................................... 28 Step 11. Set Fan and System Switches ....................................................................................... 30 Troubleshooting Guide ................................................................................................................. 31 Limited One-Year Warranty .......................................................................................................... 35 3 69-1385 Step 1. Prepare for Installation ❑ Check Table 1 to make sure this thermostat is compatible with your system. If not, return it to the retailer. For more information, call Honeywell Consumer Services, 1-800-468-1502, Monday - Friday, 7 am to 5:30 pm, Central time. Table 1. Compatibility Information. System Type Compatible with CT2095 Gas—Standing Pilot Yes Gas—Electronic Ignition Yes Gas-Fired Boilers Yesa,b Gas—Millivolt No Oil-Fired Boilers Yesa,b Oil-Fired Furnace Yes Electric Furnace Yes Electric Air Conditioning Yes Baseboard Electric (120/240 Line Volt) No Heat Pumps/Multistage Equipment No Not compatible with any 120/240 volt circuit. a Compatible with Honeywell 2-wire zone valves. Isolating relay required for 3-wire thermostats for zone valves. Not compatible with 2-wire White-Rodgers no. 1361 valves. b Compatible with hot water baseboard systems. Does not work efficiently on steam or gravity systems. 4 69-1385 ❑ Acquire tools and items as needed (see illustration). Also purchase two AA alkaline batteries; we recommend Energizer® batteries. CROSS-RECESSED SCREWDRIVER HAND OR POWER DRILL WITH 3/16 INCH DRILL BIT, IF NEEDED TO DRILL HOLES IN WALL WIRE CUTTER/STRIPPER OR SHARP KNIFE, IF NEEDED TO STRIP WIRES LEVEL, IF NEEDED TO LEVEL M13544 THERMOSTAT FOR APPEARANCE 5 69-1385 Step 2. Remove Old Thermostat ❑ Loosen screws holding thermostat to ❑ subbase, wallplate or wall, and lift away. Test to be sure your heating and cooling ❑ Disconnect wires from old thermostat or systems are working properly. If either does subbase. As you disconnect each wire, not work, contact your local heating/air attach one of the enclosed labels to each old conditioning dealer. To avoid compressor terminal designation. If there are only two damage, do not operate the cooling system wires, they do not need labeling. If there is when outdoor temperature is below 50°F an extra wire that is not connected to your (10°C). ❑ old thermostat, you also do not connect it to Turn off power to the system at the furnace, your new thermostat. Keep the wires from or at the fuse/circuit breaker panel. ❑ falling back into the wall by wrapping them Carefully unpack your new thermostat and around a pencil as shown. mounting plate, saving package of screws, instructions and receipt. WIRES THROUGH ❑ Remove cover from old thermostat. If it does WALL OPENING not snap off when pulled firmly from the bottom, check for a screw used to lock on the cover. M5136 6 69-1385 Replacing a Clock Thermostat that has those systems so return the product to the retailer. If you want information about the C or C1 Clock Terminals? programmable thermostats that work with your If you are replacing a Honeywell Chronotherm® system, call Honeywell Consumer Services at Thermostat, you may find one or two wires that 1-800-468-1502. go to the C or C1 clock terminals on the Chronotherm® Thermostat wiring wallplate. Do not allow them to touch, or you can damage Three thermostat wires? your transformer. Disconnect the wires and If you have three wires for heating only and can wrap them separately, using electrical tape. Do operate the fan using the fan On switch, this not wrap them together. Place the wires where thermostat works with your system. However, they do not interfere with the operation of the some hot water (zoned) heating systems have new thermostat. Record the colors and terminal three thermostat wires. The thermostat does designation labels of the remaining wires. not work without installing an isolating relay on these systems. For details, call Honeywell Six or more wires? Consumer Services at 1-800-468-1502. If there are six or more wires (excluding clock wires attached to terminals), you probably have a variation of a heat pump or multistage system. This thermostat is not compatible with 7 69-1385 Step 3. Install Batteries IMPORTANT Batteries must be installed for the pro- gramming and operation of the ther- mostat and heating/cooling system. ❑ Purchase two AA alkaline batteries; non- alkaline batteries do not last as long, and can leak, causing damage to the thermostat or the wall surface. We recommend Energizer® batteries. ❑ Open the top cover of thermostat to access control panel and battery compartment. ❑ Make sure the thermostat is set to the Off BATTERY position. DOOR COVER ❑ Use a coin to remove the battery cover. REMOVING BATTERY DOOR M12492 8 69-1385 ❑ Install the fresh batteries as shown, making After the batteries are completely dead, the sure positive and negative terminals are bAtLo indication disappears, leaving a oriented correctly. completely blank display. ❑ Replace the battery cover. As the batteries run low, a bAt Lo indicator INSTALL TWO AA ALKALINE flashes for one to two months before the BATTERIES AS SHOWN batteries run out completely. Replace the batteries as soon as possible after the indicator starts flashing. If you do not replace the batteries sometime during the flashing bAt Lo, the indicator eventually stops flashing. bAt Lo then stays on without flashing, indicating the thermostat and heating/cooling system have stopped working and the batteries are almost completely dead. M1713 9 69-1385 Press down on the left ends of batteries to IMPORTANT remove them. If you insert the new batteries Although the thermostat has a low bat- within 20 to 30 seconds of removing the old tery indicator, replace the batteries ones, you do not need to reprogram the once a year to prevent the thermostat thermostat. However, if the display is blank, the and heating/cooling system from shut- batteries are dead or incorrectly installed and ting down due to lack of battery power. you must reprogram. See Step 4. As a precaution, when leaving home for longer than a month, change bat- teries before you leave to prevent the system from shutting down due to lack of battery power. 10 69-1385 Step 4. Program Thermostat • WAKE is the time period you want the house at a comfortable temperature when you get After the batteries are installed, the thermostat up and while you get ready for work or can be easily programmed in your hand before school. (This is a higher temperature during it is installed on the wall. heating season and a lower temperature dur- ing cooling season.) If you prefer to program the thermostat after it is • LEAVE is the time period you can set for an installed on the wall, go to Step 7 and return energy-saving temperature while you are later to this programming section. away at work or school. (This is a lower tem- perature during heating season and a higher The Personal Programming Chart, Tables 2 and temperature during cooling season.) 3, may be helpful for planning your program • RETURN is the time period you want the schedule of time and temperature settings for house at a comfortable temperature for activ- various times of the day. ities before bedtime. (This is a higher tem- perature during heating season and a lower Four time periods are available during temperature during cooling season.) weekdays — WAKE, LEAVE, RETURN, and • SLEEP is the time period you can set for an SLEEP; view these periods individually on the energy-saving temperature while you are display as you press the Weekday key. sleeping. (This is a lower temperature during the heating season and a higher tem- perature during the cooling season.) 11 69-1385 Set one schedule for weekdays and another for If no program is entered for the weekends, the weekends because your requirements are thermostat operates on the weekday SLEEP usually different for each. Also, during week- program all weekend. ends, only the WAKE and SLEEP time periods are available. Before programming, remove the clear plastic overlay covering the display. Fill in the times and temperatures you desire for weekdays and weekends. If you decide not to When pressing the keys, use the ball of your program the thermostat, it automatically con- finger or a soft pencil eraser. Using sharp finger- trols heating at 68°F (20°C), and cooling at 78°F nails or pencil points can damage the keypad. (26°C), 24 hours a day. Also, you do not need to enter a time and temperature program for all If you make an error at any time during program- periods if your schedule does not require it. For ming, just press the Run Program key, and example, a house that is occupied during week- continue again at the previous step in your days would require programs only for WAKE sequence. and SLEEP. 12 69-1385 Table 2. Personal Programming Chart for Heating. Days of Week Heating Program Start Time Heating Temperaturea Weekdays WAKE LEAVE RETURN SLEEP Weekendsb WAKE SLEEP a The temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C). b If you decide not to enter weekend programs, the thermostat operates on the weekday SLEEP pro- gram all weekend. 13 69-1385 . Table 3. Personal Programming Chart for Cooling. Days of Week Cooling Program Start Time Cooling Temperaturea Weekdays WAKE LEAVE RETURN SLEEP Weekendsb WAKE SLEEP a The temperatures cannot be set any higher than 88°F (31°C) or any lower than 45°F (7°C). b If you decide not to enter weekend programs, the thermostat operates on the weekday SLEEP pro- gram all weekend. 14 69-1385 NOTE: Batteries are required for operation and programming. When inserting batteries, set the System switch to Off. Remove the battery door (on the thermostat left side) using a coin at the bottom. Follow instructions in Step 3. Also see the label inside the battery cover for abbreviated programming procedures for your thermostat. Set Current Time/Day Time Clock/Day To set time, press and release once, press until current shows. To set day, press and Time Clock/Day Run Program release again, press until current day shows; then press . Heating Program Weekday With System switch at Heat, press and release once. WAKE, MON FRI (Monday-Friday), and SET appear on display. Time TEMP Use to program WAKE time and to program WAKE temperature for MON FRI (Monday-Friday). Repeat sequence for LEAVE, RETURN, SLEEP. 15 69-1385 Time Weekend Press until SAT SUN (Saturday-Sunday), WAKE and SET appear on display. Use to program TEMP WAKE time and to program WAKE temperature for SAT SUN (Saturday-Sunday). Run Program Repeat sequence for SLEEP. Press and release to start the program. Cooling Program With System switch at Cool, follow the same instructions as for the Heating Program. Run Program After programming, adjust the Fan and System switches, as desired. Press and release to start the program. 16 69-1385 Operating Your Thermostat System switch must be set to Heat or Cool to perform the following: TEMP Temporarily Change Temperature for current period only — Press ; temporary indicator shows Run Program on display and cancels itself at the next scheduled change; to cancel sooner, press . TEMP Hold Temp Hold a Temperature Indefinitely (such as when on vacation) — Press and ; HOLD Run Program appears on display; to cancel, press . Present Set Check Current Temperature Setting — Press . Weekday Weekend Check Programs — Press , repeatedly to see each time and temperature; then press Run Program . 17 69-1385 Weekday Weekend Clear Cancel Program — Press , until program to cancel shows; then press . Usage Check Usage — Press to see length of time heat or air conditioning has run today since Clear midnight; press again for yesterday’s usage, press again for cumulative; press to clear Run Program cumulative reading, if desired; then press . Permanently Change a Program — Repeat Heating Program or Cooling Program steps, as applicable. Run Program Return to Normal Program or Start Program — Press . 18 69-1385 Step 5. Adjust Fan Operation as a guide. The system on-time should be optimized according to the type of system to Switch, As Required maximize comfort. Setting the screw “out one ❑ The thermostat fan operation switch, labeled turn” means turning the screw approximately FUEL SWITCH (see illustration) is factory-set 360° counterclockwise, or about one com- in the F position. This is the correct setting for plete turn. most systems. If your system is an electric heat system, set the switch to E to allow the THERMOSTAT BACK fan to turn on immediately with the heating in A C DISPLAY °F C–IN ADJUST SCREWS THROUGH HOLES DISPLAY °C C–OUT TO SELECT OPERATION DESIRED a system when the G terminal is connected. FUEL SWITCH 1 TURN HEATING SYSTEM POSITION B D WARM AIR A–IN B–IN F FURNACE HOT WATER A–OUT B–IN F BOILER 1 TURN ELECTRIC A–IN B–OUT E Step 6. Adjust System On-Time, FURNACE 1 TURN W Y G FOR HIGH EFFICIENCY FURNACE (90%+ AFUE) °F/°C, As Required ADJUST: SCREW A–OUT ONE TURN SCREW B–IN FUEL SWITCH – F POSITION ❑ The thermostat on-time is factory-set for a FUEL SWITCH warm air, gas or oil heating system. If you are F E R Rc installing it on another type of system, adjust the on-time accordingly by setting screws A M8796A and B on the back of the thermostat. Use the heating system table shown in the illustration 19 69-1385 In the unlikely event that you want a longer IMPORTANT furnace on-time, readjust screws A and/or B as When using a high efficiency furnace follows: such as a 90 percent or greater Aver- age Fuel Utilization Efficiency (AFUE) First, turn both screws in completely, then unit, adjust screw A out one turn and adjust for system type: leave screw B in. • Warm Air Furnace—Set at the Hot Water setting (A—out one turn, B—leave in). ❑ The thermostat is set to read the temperature • Electric Furnace—Leave at the Warm Air in degrees Fahrenheit. If readings are Furnace setting (A—leave in, B—leave in). desired in degrees Celsius, adjust screw C out one turn. NOTE: This thermostat does not have a set- ting for steam/gravity air; cycles would not be long enough for accurate tem- perature control. 20 69-1385 Step 7. Mount Thermostat WALL ANCHORS (2) Mounting Plate WIRES THROUGH ❑ Position mounting plate on wall. Use level to WALL OPENING make sure mounting plate is level. Use a pencil to mark the two mounting holes. WALL ❑ Remove mounting plate from wall, and drill 3/16-inch holes in wall (if drywall) as marked. For firmer material such as plaster or wood, drill 7/32-inch holes. Gently tap anchors (provided) into drilled holes until flush with the MOUNTING wall. PLATE ❑ Reposition mounting plate over holes, pulling wires through wiring opening. ❑ Loosely insert two mounting screws into MOUNTING SCREWS (2) M1718 holes. 21 69-1385 ❑ Level for appearance only; thermostat functions properly even when not level. LEVEL ❑ Tighten mounting screws. M1714A 22 69-1385 Step 8. Wire Thermostat Terminals NOTE: All wiring must comply with local codes and ordinances. If unsure about house- METHOD TO INCREASE WIRE LENGTH WIRE NUT SIZE FOR TWO 18-GAUGE WIRES hold wiring procedures, call your local heating/air conditioning contractor. ❑ Refer to the labels you placed on the terminal WIRE 6 IN. (152 MM) FROM OF 18-GAUGE wires when you removed your old thermostat. WALL THERMOSTAT WIRE. MATCH Match the letter of your old thermostat wire INSULATION COLORS with the terminal of the corresponding letter OR MARK on the back of your new thermostat. (See WIRE ENDS. M1715A wiring diagrams.) Hold the thermostat as shown in illustration to minimize need for wire ❑ In 5-wire installations only, be sure to remove extenders. If wires are still too short, use wire the factory-installed jumper connecting termi- connectors (purchased locally) to extend nals R and Rc. wires. See illustration for guidelines on using wire extenders. 23 69-1385 ❑ Loosen the terminal screws and slip each wire beneath its matching terminal. See illustrations for wire insertion technique. ❑ Securely tighten terminals. ❑ Plug the hole in the wall with insulation to help prevent drafts from adversely affecting thermostat operation. JUMPER (FACTORY- INSERT INSTALLED). REMOVE STRAIGHT IF 5-WIRE SYSTEM 5/16 in. UNDER (8 mm) c R SCREW HEAD R STRIP END OF WIRE VISIBLE HERE G WY M1712B M3002A 24 69-1385 2-WIRE HEAT-ONLY (JUMPER INTACT) 4-WIRE HEAT/COOL (JUMPER INTACT) A C A C B D B D W Y G JUMPER W Y G JUMPER R Rc R Rc HEATING HEATING COOLING RELAY OR RELAY OR CONTACTOR VALVE COIL L1 VALVE COIL COIL (HOT) 1 L2 FAN RELAY L1 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND (HOT) OVERLOAD PROTECTION AS REQUIRED. M1709B L2 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. M1710B 25 69-1385 5-WIRE HEAT/COOL (JUMPER REMOVED) 3-WIRE COOL-ONLY (JUMPER INTACT) A C A C B D B D W Y G W Y G JUMPER R Rc R Rc HEATING FAN RELAY OR RELAY COOLING VALVE COIL CONTACTOR COIL COOLING CONTACTOR FAN 1 COIL 1 RELAY L1 (HOT) L1 L2 (HOT) L2 L2 L1 (HOT) 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. M848A OVERLOAD PROTECTION AS REQUIRED. M1711C 26 69-1385 Step 9. Mount Thermostat NOTE: To remove thermostat from wall, first pull out at bottom of thermostat, then remove top. A. ENGAGE TABS AT TOP OF B. PRESS LOWER EDGE C. SWING OPEN COVER TO THERMOSTAT AND SUBBASE. OF CASE TO LATCH. CHECK OPERATION. AM TU LEAVE Clock/Day Time TEMP Run Program Weekday Hold Temp Weekend Clear Usage Present Set Fan System Auto On Cool Off Heat M13545 27 69-1385 Step 10. Check Thermostat Move the System switch to Cool Off Heat Heat and the Fan switch to Operation After Programming Auto. M1703 and Installing Auto On M1705 Heating Press TEMP key until the set- TEMP Do not check heating system operation by ting is about 10°F (6°C) above jumpering thermostat terminals such as gas room temperature. Heating valve, zone valve, and oil burner control at the should start and the fan should primary control. This damages the thermostat. run after a short delay (immedi- Instead, jumper R and W wires at the ately if fan operation switch is set to E position). thermostat. Press TEMP key until setting is about 10°F (6°C) below room temperature. The heating equip- ment should shut off. 28 69-1385 Cooling Move the System switch to Cool Off Heat To avoid possible compressor damage, do not Cool and the Fan switch to Auto. operate the cooling system when outdoor M1704 temperature is below 50°F (10°C). See Auto On compressor manufacturer instructions. M1705 IMPORTANT Press TEMP key until setting is TEMP When cooling setting is changed, ther- about 10°F (6°C) below room mostat delays up to five minutes temperature. The cooling before turning on the air conditioner. equipment and fan should start. This delay protects the compressor. Press TEMP key until the setting is about 10°F (6°C) above room temperature. The cooling equipment and fan should stop. Move the System switch to Off; Cool Off Heat keep the Fan switch at Auto. The system and fan should be M1707 off. Auto On 29 69-1385 Step 11. Set Fan and System Switches First set the Fan switch. Then set the System switch. Fan Auto: Normal setting for most Auto On Cool: The thermostat controls Cool Off Heat homes. A single-speed fan will your air conditioning turn on automatically with the air system. conditioner or furnace. A two-speed fan usually runs on high with the air conditioner Off: Both the heating and air Cool Off Heat and on low with the furnace. conditioning systems are off. Fan On: The fan runs continuously. Auto On Use for improved air circulation Heat: The thermostat Cool Off Heat during special occasions or for controls your heating more efficient electronic air system. cleaning. (In a heat-only system, fan runs continuously only if fan relay is connected to the thermostat.) 30 69-1385 Troubleshooting Guide If... Then... Display does not come on. Set the System switch to Off. Remove batteries. Insert them backward for at least five seconds to reset the thermostat. Replace batteries correctly. Display should come on. Make sure batteries are fresh and installed correctly. Temperature display does You have reached the temperature setting limit. The setting range is not go lower than 45°F 45°F to 88°F (7° to 31°C). (7°C) or higher than 88°F (31°C) during programming. Temperature change occurs Check the program times for the questionable period. Be sure that AM at wrong times. and PM indications are correct. Make sure the current day and time are correct. Reprogram, if necessary. 31 69-1385 If... Then... Heating does not come on. Check that the System switch is set to Heat. Make sure the heating setpoint is above the room temperature. Check the system fuse or circuit breaker and replace or reset, if necessary. Make sure the System switch is in the On position; set it to On if it is in the Off position. If temperature setting is higher than the current temperature and the display says HEAT, contact Honeywell Consumer Services at 1-800- 468-1502. Cooling does not come on. Check that the System switch is set to Cool. Make sure the cooling setpoint is below the room temperature. Check the system fuse or circuit breaker and replace or reset, if necessary. Make sure the System switch at the air conditioner is in the On position; set it to On if it is in the Off position. 32 69-1385 If... Then... Cooling does not come on The thermostat has a built-in time delay on cooling. Allow five to ten (Continued). minutes after changing the setting before the air conditioner starts. If temperature setting is lower than current temperature, and the display says COOL, move the System switch from Cool to Off for ten minutes. After ten minutes, return the switch to the Cool position. If air conditioner comes on, compressor may have reached its high-limit temperature protection and shut down.If air conditioner does not come on after the ten minutes and the display says COOL, contact Honeywell Consumer Services at 1-800-468-1502. If two- or four-wire installation, verify R-Rc jumper is installed. The house is too warm or Press Present Set key to check the current temperature setting. too cool. If desired, change the temperature setting. See Cooling Program section. SYSTEM ON indicator is Allow time for the furnace to heat up and the fan to come on before lighted, but no heat is checking for heat at the register. (Check to make sure system on-time coming from the registers. is set correctly. See Step 6.) 33 69-1385 Toll-free Customer Assistance For all questions concerning this thermostat, please read and follow the instructions. If additional assistance is needed, call Honeywell Consumer Services at 1-800-468-1502, Monday - Friday, 7:00 a.m. - 5:30 p.m. Central time. Before you call, please have the following information available—thermostat model number and date code, type of heating/cooling system (hot water, warm air, oil, gas, etc.), and number of wires connected to the thermostat. NOTICE This equipment is a Class B digital apparatus, which complies with Canadian Radio Interference Regulations, CRC c.1374. 34 69-1385 Limited One-Year Warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time. If the product is defective, (i) return it, with a bill of sale or other dated proof of purchase, to the retailer from which you purchased it, or (ii) package it carefully, along with proof of purchase (including date of purchase) and a short description of the malfunction, and mail it, postage prepaid, to the following address: Honeywell Inc. Canada: Honeywell Limited/Honeywell Limitée Return Goods Department Product ServicesON15-FFE 1050 Berkshire Lane 740 Ellesmere Road Plymouth, MN 55441-4437 Scarborough, Ontario M1P 2V9 This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. 35 69-1385 THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write our Customer Assistance Center, Honeywell Inc., P.O. Box 524, Minneapolis, MN 55440-0524 or call 1-800-468-1502, Monday-Friday, 7:00 a.m. to 5:30 p.m., Central time. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 155 Gordon Baker Road, North York, Ontario M2H 2C9. 36 69-1385 TYPICAL ENERGY SAVINGS FOR REPRESENTATIVE CITIES IN THE U.S. AND CANADA Savings for Once-A-Day Savings for Twice-A-Day Savings for 5°F (3°) 10°F (5°C) decrease 10°F (5°C) decrease* summer increase 30% 28% 26% 24% 22% 20% 18% 16% 14% 12% 10% 8% 6% Approximate percentage of energy cost savings 4% 2% Minneapolis Edmonton Calgary Halifax VancouverBuffalo Denver Boston Cincinnati New York Louisville San Dallas Los Angeles San Diego St. Paul Regina Moncton Cleveland Des Moines Chicago Kansas City Philadelphia Portland Francisco Atlanta Montreal Winnipeg North Bay Milwaukee Omaha Detroit St. Louis Seattle Wash., D C Ottawa Quebec Salt Lake Pittsburgh Columbus Toronto St. John's City Indianapolis *Based on 10°F (5°C) decrease—(5°F [3°C] decrease gives approximately 55 percent of these savings). M2416A 37 69-1385 38 69-1385 39 69-1385 Home and Building Control Home and Building Control Honeywell Inc. Honeywell Limited-Honeywell Limitée Honeywell Plaza 155 Gordon Baker Road P.O. Box 524 North York, Ontario Minneapolis, MN 55408-0524 M2H 3N7 Printed in U.S.A. on recycled 69-1385 G.H. 6-00paper containing at least 10% www.honeywell.com/yourhome post-consumer paper fibers.

No comments:

Post a Comment

Popular Posts