Honeywell Thermostat R7847 User Manual - Honeywell Thermostat Manual Download

Latest

Sunday, April 5, 2020

Honeywell Thermostat R7847 User Manual

R7824, R7847, R7848, R7849,R7851,R7861, R7886 Amplifiers for 7800 SERIES Relay Modules PRODUCT DATA The R7851C Dynamic Self-Check Optical Flame Amplifier is a solid state plug-in amplifier that responds to ultraviolet signals from C7961E Dynamic Shutter-Check ultraviolet flame detectors to indicate the presence of flame when used with 7800 SERIES Relay Modules. The R7861A Self-Check Ultraviolet Flame Amplifier is a solid state plug-in amplifier that responds to an ultraviolet signal from a C7061 Self-Check Ultraviolet Flame Detector to indicate the presence of flame when used with 7800 SERIES Relay Modules. The R7886A Dynamic Self-Check Ultraviolet Amplifier is a solid state plug-in amplifier that responds to a pulsed direct current signal from a C7076A,C Ultraviolet Flame Detector with adjustable sensitivity to indicate the presence of flame when used with 7800 SERIES Relay Modules. FEATURES • Flame failure response time of 0.8 or 1 second; or 2.0 or 3.0 seconds, depending on the amplifier and relay module selected. See Table 1. • Plug-in to 7800 SERIES Relay Module through printed circuit board edge connector keyed for proper orientation. APPLICATION • Flame signal test jacks measure amplifier flame signal voltage. The R7824C Rectification Flame Amplifier is a solid state plug-in • 0.0 to 5.0 Vdc Flame signal strength reading range. amplifier that responds to a rectified signal from a C7024E,F Self- Check Ultraviolet Flame Detector to indicate the presence of • Color coded label identifies flame detection type: flame when used with an RM7824 Relay Module. — Green—rectification. Red—infrared. — Purple—ultraviolet. Blue—pulsed rectification. The R7847A,B Rectification Flame Amplifiers are solid state plug- — White—optical. in amplifiers that respond to a rectified signal from a rectification • R7847B, R7848B, R7849B Dynamic Ampli-Check® type flame detector to indicate the presence of flame when used circuitry tests all flame amplifier components 12 times per with 7800 SERIES Relay Modules. minute. The 7800 SERIES Relay Module locks out on safety shutdown with amplifier failure. The R7847C Self-Check Rectification Flame Amplifier is a solid • R7824C and R7847C Dynamic Self-Check Rectification state plug-in amplifier that responds to a rectified signal from a Amplifier, R7851C Dynamic Self-Check Optical Flame C7012E,F Self-Check Ultraviolet Flame Detector to indicate the Amplifier, R7861 Self-Check Ultraviolet Flame Amplifier presence of flame when used with 7800 SERIES Relay Modules. and R7886A Dynamic Self-Check Ultraviolet Amplifier test This is not European Community (CE) approved for EC7810, the detectors and all electronic components in the flame EC7820, EC/RM7830 or EC/RM7850 Relay Modules. detection system 12 times per minute. The 7800 SERIES Relay Module locks out on safety shutdown with flame The R7848A,B Infrared Flame Amplifiers are solid state plug-in detection system failure. amplifiers that respond to an infrared signal from a C7015 Infrared Flame Detector to indicate the presence of flame when NOTE: NOTE:R7824C, Series 2 or greater, and R7847C, used with 7800 SERIES Relay Modules. Series 4 or greater, pulse shutter when signal of 1.5 Vac is sensed. The R7849A,B Ultraviolet Flame Amplifiers are solid state plug-in amplifiers that respond to an ultraviolet signal from a C7027, Contents C7035 or C7044 Ultraviolet Flame Detector to indicate the presence of flame when used with 7800 SERIES Relay Modules. Application ........................................................................ 1 Features ........................................................................... 1 The R7851B Optical Flame Amplifiers are solid state plug-in Specifications ................................................................... 2 amplifiers that respond to optical signals from C7927, C7935, Ordering Information ......................................................... 2 C7915, and C7962 Flame Detectors to indicate the presence of Installation ........................................................................ 4 flame when used with 7800 SERIES Relay Modules. Checkout .......................................................................... 6 ® U.S. Registered Trademark Copyright © 2002 Honeywell • All Rights Reserved 65- 0109- 8 R7824, R7847, R7848, R7849,R7851,R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES SPECIFICATIONS Models: Factory Mutual Approved: Report J.I.1V9A0.AF. (R7851C Flame Detection Systems (see Table 2): Pending.) Rectification: Industrial Risk Insurers: Acceptable R7824C for use with C7024E,F Solid State Ultraviolet Detectors. Table 1. Relay Module Flame Failure R7847A for use with flame rods, rectifying photocells or Response Time (FFRT). C7012A,C Solid State Ultraviolet Detectors. R7847B for use with flame rods, rectifying photocells or Flame Failure Response C7012A,C Solid State Ultraviolet Detectors. Time (FFRT) in seconds R7847C for use with C7012E,F Solid State Ultraviolet Detectors. Relay Module 0.8 or 1 2.0 or 3.0 Infrared: R7848A for use with C7015 Infrared (lead sulfide) Detector. EC7810, EC7820, EC/RM7830, 1.0 2.0 R7848B for use with C7015 Infrared (lead sulfide) Detector. EC/RM7850 Ultraviolet: EC/RM7823, EC/RM7885, EC/ 0.8 3.0 R7849A for use with C7027/C7035/C7044 Minipeeper Ultravi- olet Detectors. RM7890, EC/RM7895, RM7896, R7849B for use with C7027/C7035/C7044 Minipeeper Ultravi- RM7888, RM7838, RM7800, olet Detectors. RM7840 R7861A for use with C7061A Ultraviolet Detector. R7886A for use with C7076A,D Ultraviolet Detectors with RM7824 N/A 3.0 adjustable sensitivity. Optical: R7851B for use with C7927, C7935, C7915 and C7962 Flame Detectors. R7851C for use with C7961E Flame Detectors. S Ð+ Flame Failure Response Time: See Table 1. Flame Signal (Volts dc): FLAME AMPLIFIER Minimum Acceptable: 1.25 Vdc. 3 Flame Signal Voltage Range (displayed on Keyboard Display (76) Module or measured with a 1M ohm/volt meter plugged into amplifier test jacks): 0.0 to 5.0 Vdc. Environmental Ratings: Ambient Temperature: 3/8 (9) Operating: -40°F to 140°F (-40°C to 60°C). 7/8 Storage: -40°F to 150°F (-40°C to 65°C). 3-9/16 (91) Humidity: Operating 85% rh continuous, noncondensing. (23) Vibration: Continuous 0.5G environment. M11460 Weight: 2.5 oz (71g), unpacked. Fig. 1. Flame amplifier dimensions in in. (mm). Dimensions: See Fig. 1 Approvals: NOTE: .NOTE: EN298 Approved: When these amplifiers are Underwriters Laboratories Inc. Listed: File no. MP268, Guide no. used with an EC7810, EC7820, EC/RM7830, or MCCZZ: R7847A, R7847B, R7847C, R7861A, R7886A, EC/RM7850 Relay Module. R7848A, R7848B, R7849A, R7849B, R7851B. (R7851C Pending.) Accessories: Underwriters Laboratories Inc. Component Recognized: File no. Flame Simulators: MP268, Guide no. MCCZZ: R7824C. Rectification: 123514A. Canadian Standards Association Certified: LR95329-3. (R7851C Ultraviolet: 203659. Pending.) Flame Detectors (ordered separately): select from Table 2. ORDERING INFORMATION When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the TRADELINE® Catalog or price sheets for complete ordering number. If you have additional questions, need further information, or would like to comment on our products or services, please write or phone: 1. Your local Home and Building Control Sales Office (check white pages of your phone directory). 2. Home and Building Control Customer Relations Honeywell, 1885 Douglas Drive North Minneapolis, Minnesota 55422-4386 In Canada—Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9. International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France, Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A. 65-0109—8 2 R7824, R7847, R7848, R7849,R7851,R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES Table 2. Flame Detection Systems. Plug-in Flame Signal Amplifiers Applicable Flame Detectors Flame Failure Response Type Color Self-Checking Model Time (sec)a Fuel Type Models Rectification Green Dymanic Self- R7824Cb,c, i 3 Gas, oil, Ultraviolet (Purple C7024E,F Check coal Peeper®) No R7847Ah 0.8/1 or 2/3 Gas Rectifying Flame Rod C7004, C7007, C7011 Holdersj Complete Assemblies: C7008, C7009, Q179 No R7847Ah 0.8/1 or Oil Rectifying Photocell C7003, C7010, C7013, 2/3 C7014d No R7847Ah 2/3 Gas, oil, Ultraviolet (Purple C7012A,C. coal Peeper®) Dynamic Ampli- R7847Be,h 0.8/1 or Gas Rectifying Flame Rod C7004, C7007, C7011 Check® 2/3 Holdersb Complete Assemblies: C7008, C7009, Q179 Dynamic Ampli- R7847Be,h 0.8/1 or Oil Rectifying Photocell C7003, C7010, C7013, Check® 2/3 C7014d Dynamic Ampli- R7847Be,h 2/3 Gas, oil, Ultraviolet (Purple C7012A,C Check® coal Peeper®) Dynamic Self- R7847Cc,f, i 2/3 Gas, oil, Ultraviolet (Purple C7012E,F Check coal Peeper®) Infrared Red No R7848A 2/3 Gas, oil, Infrared (Lead C7015 coal Sulfide) Dynamic Ampli- R7848Be 3 Gas, oil, Infrared (Lead C7015 Check® coal Sulfide) Ultraviolet Purple No R7849A 0.8/1 or Gas, oil Ultraviolet C7027, C7035, C7044g 2/3 (Minipeeper) Dynamic Ampli- R7849Bd 0.8/1 or Gas, oil Ultraviolet C7027, C7035, C7044g Check® 2/3 (Minipeeper) Dynamic Self- R7861Ac,f 0.8/1 or Gas, oil, Ultraviolet C7061 Check 2/3 coal Blue Dynamic Self- R7886Ac,f 2/3 Gas, oil, Ultraviolet (Adjustable C7076 Check coal Sensitivity) Optical White Dymanic Ampli- R7851B 0.8/1 or 2/3 Gas, oil, Optical (UV, IR, C7927, C7935, C7915, Check® coal Visible Light) C7962 Dynamic Self- R7851Cc 2/3 Gas, oil, Optical (UV only) C7961 Check coal a Flame Failure Response Time (FFRT) depends on selection of amplifier and 7800 SERIES Relay Module. b R7824C is used only with the 24 Vdc RM7824 Relay Module and C7024E,F Flame Detectors. c Circuitry tests all electronic components in flame detection system (amplifier and detector) 12 times a minute during burner operation and shuts down burner if detection system fails. d Use only Honeywell part no. 38316 Photocell. e Circuitry tests flame signal amplifier 12 times a minute during burner operation and shuts down burner if amplifier fails. f 200/220/240 Vac applications require a 120 Vac, 10 VA minimum stepdown transformer (not provided) to drive the shutter. Applies to R7847C series 3 or greater; R7886A series 2 or greater; R7861 series 1 or greater. Fig. 2 shows flame detector wiring. g Use C7027, C7035 and C7044 Flame Detectors only on burners that cycle on-off at least once every twenty-four hours. Use C7012E,F Flame Detector with R7847C Amplifier, C7061A Ultraviolet Detector with R7861A Amplifier or C7076A Flame Detector with R7886A Amplifier as ultraviolet flame detection system for appliances with burners that remain on continuously for twenty-four hours or longer. h R7847A,B Amplifiers with 0.8/1 second FFRT should not be used with C7012A,C Solid State Ultraviolet Detectors. i R7824C Series 2 and greater and R7847C Series 4 and greater check flame detector system when flame reaches 1.5 Vdc or at 4.5 seconds, whichever occurs first. j Order flame rod separately; see flame detector Instructions for holder. 3 65-0109—8 R7824, R7847, R7848, R7849,R7851,R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES 1. Align the amplifier circuit board edge connector with the keyed receptacle on the 7800 SERIES Relay Module. CAUTION Be sure the amplifier nameplate faces away from the Equipment Damage Hazard. Relay Module. Incorrect combination of relay module, amplifier 2. Push in the amplifier until the circuit board is fully and flame detector can cause equipment damage. inserted into the receptacle and then push the amplifier In infrared applications (C7015 Infrared Flame toward the 7800 SERIES Relay Module retaining clasp. Detector and R7848 Amplifier) using the RM7890 3. Be sure the amplifier is firmly in place. Relay Module with software version 4004 or less 4. Perform all required checkout tests. requires a ten-second delay to start sequence. This applies only to the initial power of the RM7890. Installing Flame Detector INSTALLATION NOTE: NOTE:Table 2 lists flame detection systems available for use with 7800 SERIES Relay Modules. Be sure to use the correct combination of amplifier and flame When Installing this Product... detector. 1. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous Proper flame detector installation is the basis of a safe and condition. reliable flame safeguard installation. Refer to the Instructions 2. Check the ratings given in the instructions and on the packed with the flame detector and the equipment manufac- product to make sure the product is suitable for your turer instructions. application. 3. Installer must be a trained, experienced, flame Keep the flame signal leadwires as short as possible from the safeguard control technician. flame detector to the wiring subbase. Capacitance increases 4. After installation is complete, check out the product with leadwire length, reducing the signal strength. The operation as provided in these instructions. maximum permissible leadwire length depends on the type of flame detector, leadwire and conduit. However, the ultimate limiting factor for the flame detector leadwire is the flame WARNING signal; see Table 3 in the Checkout section. Electric Shock Hazard. Can cause electrical shock, serious injury or death. Disconnect the power supply before beginning installation. More than one power supply disconnection can be involved. IMPORTANT 1. Wiring must comply with all applicable codes, ordinances and regulations 2. Wiring (where required) must comply with NEC Class 1 (Line Voltage) wiring. 3. Perform all required checkout tests after installation is complete. CAUTION Equipment Damage Hazard. Can cause equipment damage. Disconnect 7800 SERIES Relay Module power before Fig. 2. Installing flame signal amplifier. removing amplifier. Wiring Installing Plug-In Flame Signal Amplifier (Fig. 2) WARNING Electrical Shock Hazard. Can cause electrical shock or equipment damage. WARNING Disconnect power supply before beginning installation. Electric Shock Hazard. More than one disconnection can be involved. Can cause electrical shock, serious injury or death. 1. Remove the 7800 SERIES Relay Module from the Disconnect the power supply before beginning wiring subbase. installation. More than one power supply 2. Refer to Fig. 3 for proper flame detector wiring. disconnection can be involved. 65-0109—8 4 R7824, R7847, R7848, R7849,R7851,R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES PHOTOCELL FLAME ROD C7076A,D ULTRAVIOLET DETECTOR X F X F REMOTE SENSOR X G X G 6 F 7 EARTH 3a 3b 2b GROUND 5 G 8 2a INFRARED (C7015) 4 SHUTTER L1 1 WHITE C7076A F OR BROWN 3 SHUTTER L2 2 C7076D G TERMINAL BLOCK 3 L1 (HOT) ULTRAVIOLET (C7027/C7035/C7044) L2 (COMMON) F BLUE 7800 SERIES 1 G WHITE F G L2 5 22 OPTICAL C7927A F BLUE SOLID STATE SELF-CHECKING 1 WHITE ULTRAVIOLET (C7012E,F) G SOLID STATE ULTRAVIOLET (C7012A,C, C7961E) 4 F BLUE 2 G YELLOW 22 WHITE 3 L2 WHITE L1 BLACK BLUE 2 F L2 BLACK G YELLOW L1 BLACK L2 BLACK 5 GND GREEN SOLID STATE SELF-CHECKING SOLID STATE SELF-CHECKING ULTRAVIOLET (C7024E,F Ð E SHOWN) ULTRAVIOLET (C7061A) F BLUE BLUE F 2 G YELLOW 2 WHITE G YELLOW 22 WHITE 3 L2 WHITE 22 3 RED N WHITE L2 BLACK 1 ! CAUTION: EQUIPMENT DAMAGE HAZARD. INCORRECT WIRING POLARITY CAN DAMAGE OR DESTROY UV SENSING TUBES. CONNECT FLAME DETECTOR WIRES ACCORDING TO FOOTNOTES 1 AND 2 TO PREVENT UV SENSING TUBE DAMAGE.FLAME DETECTOR LEADS ARE COLOR CODED. THE BLUE LEAD MUST BE CONNECTED TO THE F TERMINAL AND THE WHITE MUST BE CONNECTED TO THE G TERMINAL. THE UV SENSING TUBE IS POLARITY SENSITIVE. 2 FLAME DETECTOR LEADS ARE COLOR CODED. THE BLUE LEAD MUST BE CONNECTED TO THE F TERMINAL AND THE YELLOW MUST BE CONNECTED TO THE G TERMINAL. THE UV SENSING TUBE IS POLARITY SENSITIVE. 3 ! CAUTION: EQUIPMENT DAMAGE HAZARD. INCORRECT VOLTAGE CAN DAMAGE SHUTTER MECHANISM ONLY ON EC7800 SERIES RELAY MODULES. INSTALL A 200/220/240 VAC TO 120 VAC, 10VA MINIMUM, STEPDOWN TRANSFORMER (NOT PROVIDED) TO DRIVE THE SHUTTER MECHANISM. 4 DO NOT USE 0.8/1 SECOND FFRT AMPLIFIER WITH C7012A,C FLAME DETECTOR. 5 GND (GREEN) LEAD WIRE ON C7961E ONLY. M20309 Fig. 3. Flame detector wiring. 5 65-0109—8 R7824, R7847, R7848, R7849,R7851,R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES 3. Disconnect power supply before making wiring connections to prevent electrical shock and equipment damage. CAUTION 4. All wiring must comply with appropriate electrical codes, Equipment Damage Hazard. ordinances and regulations including NEC Class 1 (Line Improper wiring can destroy ultraviolet sensing Voltage) wiring where required. tube. 5. Use recommended wire size and type no. 18 copper Carefully follow polarity sensitive wiring instructions for conductors TTW(60C) or THW (75C) or THNN(90C). the C7027, C7035, C7044, C7012, C7024, C7061, 6. Use recommended wire routing: C7961 and C7076. Reversing the leadwires, even a. Keep the flame signal leadwire as short as possible momentarily, can destroy the ultraviolet sensing tube. from the detector to the 7800 SERIES Relay Module. The maximum permissible leadwire length depends on the type of leadwire, conduit type and leadwire diameter. The ultimate limiting factor for flame signal POSITIVE (+) leadwire length is the flame signal voltage. METER LEAD NEGATIVE (-) ONE b. Do not run high voltage ignition transformer wires in METER LEAD MEGOHM/VOLT the same conduit with the flame detection wiring. METER c. If the flame detector leadwires are not long enough FLAME SIMULATOR to reach the 7800 SERIES Relay Module electrical TEST JACK connectors, make splices in a junction box. (1) Enclose scanner wiring without armor cable in metal cable or conduit. (2) Follow flame detector Instructions. 7. Check wiring, see Fig. 4. 8. Install 7800 SERIES Relay Module. 9. Restore power to the 7800 SERIES Relay Module. Flame detector wiring is shown in Fig. 3. CHECKOUT M11459A Preliminary Inspection Fig. 4. Flame signal measurement with meter. Make certain that: 1. Connect blue leadwire from detector to terminal F and 1. Wiring connections are correct and all terminal screws white leadwire from C7027/C7035/C7044/C7061 to and electrical connections are tight. terminal G. 2. Proper flame failure response time is selected. 2. Connect blue leadwire from detector to terminal F and 3. Amplifier is securely mounted on the 7800 SERIES yellow leadwire from C7012/C7024/C7961 to terminal Relay Module. G. 4. Detectors are properly positioned and cleaned 3. Follow lightoff Instructions for applicable 7800 SERIES according to Detector Instructions. Relay Module. 5. Correct combination of amplifier and flame detector is used. Measuring Flame Signal With Keyboard Flame Signal Measurement (Fig. 4) Display Module Flame signal can be measured at the Flame Signal Test Consult Instructions for applicable 7800 SERIES Relay Jacks, see Fig. 4, and at the Keyboard Display Module. Module or Keyboard Display Module. Measure the flame signal at the appropriate times defined in the Checkout section; see applicable 7800 SERIES Relay Measuring Flame Signal with a Volt Module Instructions. See Table 3 for acceptable and maximum flame signal voltage strengths. Ohmmeter Two test jacks, positive and negative (Com) are accessible on the top of the amplifier when plugged into the 7800 SERIES Relay Module. These jacks are provided for monitoring flame signal strength. Use a one megohm/volt meter to measure the flame signal strength. Connect the positive meter lead (red) to the positive (+) amplifier test jack and the negative meter lead (black) to the negative (-) amplifier test jack. The test jacks use standard 0.180 inch diameter voltmeter probes. A minimum 1.25 Vdc flame signal is required. 65-0109—8 6 Table 3. Flame signal. Minimum Acceptable Flame Detector Flame Signal Amplifier Steady dc Voltagea Maximum Expected dc Voltage Flame Rod Photocell R7847A,Bb 1.25 Vdc 5.0 Vdc at Keyboard Display Module C7012A,Cc or on volt-ohmmeter. C7012E,Fc R7847Cd,e C7015A R7848A,Bb C7024E,F R7824Cd,e C7027A R7849A,Bb C7035A C7044A C7927 R7851Bb C7935 C7915 C7962 C7061A R7861Ad C7076A,D R7886Ad C7961E R7851Cd a This minimum or stronger signal can be easily obtained if the detector is correctly installed and positioned to properly sense the flame. Obtain this voltage before completing checkout. b The flame amplifiers are Ampli-Check® type. c Adjust slightly, or face the pipe down, or extend the sight pipe on C7012A,C,E,F applications to obtain a maximum flame signal reading less than 5.0 volts. d The flame signal amplifier circuitry is tested one-half second every five seconds during burner operation and shuts down the burner if the amplifier fails (all installations). e R7824C, Series 2 or greater, and R7847C, Series 4 or greater, pulse the shutter when the flame signal reaches 1.5 Vdc. The flame signal for the pilot alone, the main burner flame 5. With the burner running, check the temperature at the alone, and both together must be steady and a minimum of detector. If it exceeds the detector maximum rated 1.25V. If the flame signal is unsteady, or less than the temperature: minimum acceptable voltage, check the flame detector a. Add a heat block to stop conducted heat traveling installation and circuitry in the following procedure. up the sight pipe. b. Add a shield or screen to reflect radiated heat. 1. Check the supply voltages at terminals (L1) and L2 (N). c. Add cooling (refer to sight pipe ventilation in the Make sure the master switch is closed, connections are detector Instructions). correct, and the power supply is of the correct voltage 6. Make sure that the flame adjustment is not too lean. and frequency and is sinusoidal. 7. Make sure the optical detector is properly sighting the 2. Check the detector wiring for defects including: flame. a. Incorrect connections. 8. If necessary, resight or reposition the detector. b. Wrong type of wire. 9. If you cannot obtain proper operation, replace the c. Deteriorated wire. plug-in amplifier. d. Open circuits. 10. If you cannot yet obtain proper operation, replace the e. Short circuits. flame detector. f. Leakage paths caused by moisture, soot or accu- mulated dirt. IMPORTANT 3. For a flame rod, make sure: If you make any changes to the flame detection a. There is enough ground area. system, repeat all required Checkout tests in b. The flame rod is properly located in the flame. Checkout section of the Instructions for the c. Temperature at the flame rod insulator is no greater applicable 7800 SERIES Relay Module. than 500¡F (260¡C). 4. For all optical detectors, clean the detector viewing win- dow, lens, and inside of the sight pipe as applicable. 7 65-0109—8 Automation and Control Solutions Honeywell International Honeywell Europe S.A. Honeywell Latin American Honeywell Honeywell Limited-Honeywell Limitée Control Products 3 Avenue du Bourget Region 1985 Douglas Drive North 35 Dynamic Drive Honeywell Building 1140 Brussels 480 Sawgrass Corporate Parkway Golden Valley, MN 55422 Scarborough, Ontario 17 Changi Business Park Central 1 Belgium Suite 200 M1V 4Z9 Singapore 486073 Sunrise FL 33325 Printed in U.S.A. on recycled 65-0109—8 G.R. Rev. 01-02 paper containing at least 10% www.honeywell.com post-consumer paper fibers.

No comments:

Post a Comment

Popular Posts