Honeywell Thermostat RRTH9590WF User Manual - Honeywell Thermostat Manual Download

Latest

Sunday, April 5, 2020

Honeywell Thermostat RRTH9590WF User Manual

Quick Start Guide Wi-Fi Color Touchscreen Programmable Thermostat RTH9590 Wi-Fi With Voice Control Welcome Getting set up and ready is simple. 1 Install your thermostat. 2 Connect your home Wi-Fi network. 3 Register online for remote access. Before you begin You will also need: View the installation video at You will need your camera • Small screw driver wifithermostat.com/support to take a picture of your old • Pen wire connections. • Thermostat ID card • Your home Wi-Fi network password 2 1 Install your thermostat 1.1 Switch OFF power to your heating/cooling system 1.1a Important! To protect your or equipment, switch OFF the power to your heating/ cooling system at the breaker box or the system switch. Circuit Heating/coolingM31535 1.1b Confirm power is OFF. breaker system power Try to turn on heating/ box switch cooling equipment by changing temperature on your old thermostat. Your power is OFF if your This thermostat works with common 24 system does not turn ON. volt systems such as forced air, hydronic, heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas fireplace, or with 120/240 volt systems such as baseboard electric heat. 3 1.2 Remove old thermostat faceplate and leave wires connected Note: You will need a picture of your wire 1.2a Take a picture of the wire connections to wire the connections for later new thermostat. reference. 1.2b If no wire is connected to a terminal labeled C or no C terminal exists on the old thermostat, view the Alternate Wiring videos at wifithermostat.com/videos C Important! C wire is required and is the power source for your Terminal M33823A thermostat. Without a C wire, your designation thermostat will not power up. If you have an older thermostat with a sealed mercury tube, see warning page for proper disposal instructions. 4 1.3 Label wires Sticky tag Do not label by wire color. Use the supplied sticky tags to label each wire as you disconnect it. Label wires according to old thermostat terminal designations, not by wire color. Note: If no tag matches a terminal designation, write the appropriate letter on a blank sticky tag. Note: Wrap the wires around a pencil Blank tags to prevent them from falling back into the wall. 1.4 Remove wallplate Remove the old wallplate from C the wall after all wires are C labeled and disconnected. MCR31537 Terminal designation 5 1.5 Mount wallplate for Wi-Fi thermostat Mount your new wallplate using screws and anchors included with the thermostat. If necessary: Wallplate LEVEL • Drill 3/16-in holes for drywall HERE • Drill 7/32-in holes for plaster W- C O/B K Y You may be able to use Rc G Note: W2- R Aux/E Y2 your existing wall anchors. Hold L the wallplate up to the existing anchors to check for alignment. Y W R G C MCR34499 6 1.6 Connect wires Important! C wire is required and Note: The wiring for your application is the power source. Without a C wire, might be different than the wiring your thermostat will not power up. shown below. View the Alternate Wiring videos Terminal release at wifithermostat.com/videos 1.6a Starting with the C Wire, match C W W W- the sticky tag on the wire to the C O/B Y Y terminal labels. K Y Rc G G 1.6b Straighten wire and gently slide R W2- R Aux/E into terminal hole until it clicks Y2 into place. (If you need to L remove a wire, use a pen tip to EXAMPLE WIRING press the terminal release and Yours may look different then pull the wire out.) Note: Refer to the wiring picture Remove jumper loop ONLYMCR34540 if you took in Step 1.2. you have both R and Rc wires. Tip: To make it easier to slide the Labels don’t match or have wire into place, use a pen tip to heat pump system? hold down the terminal release. See User Guide. 7 1.6c In the image on the right, check Important! the box next to each connection. Check the box for each wire You will use this checklist in you connect. You will need Step 1.9. this information in Step 1.9. 1.6d Verify wire is firmly secured by gently pulling on wire. C W-O/B 1.6e Repeat steps a–d for all other K Y wires. Rc G 1.6f Push any excess wire back into R W2-Aux/E the wall opening after all wires Y2 are installed. L Note: The L terminal on the lower right is used only for Heat Pump systems. Labels don’t match or have heat pump system? Note: If the old thermostat for Heat See User Guide. Pump System has separate wires on Aux and E, use a wire nut to attach both wires to a separate wire. Slide this third wire into the W2-Aux/E terminal. 8 1.7 Attach thermostat LEVEL HERE to wallplate Wallplate Align the thermostat with wallplate and snap into place. Thermostat 1.8 Switch heating/cooling system ON Important! M34498 1.8a Verify that the C wire is connected at the thermostat and at the heating/cooling or system. 1.8b Make sure the heating/ cooling system door is firmly secured. Circuit Heating/coolingM31535 1.8c Switch power back ON for breaker system power your heating/cooling system box switch at the breaker box or its power switch. 9 1.9 Select setup Before connecting to your Wi-Fi network, you need to set initial thermostat options to define your heating/cooling system: • Language Next • Home or business Follow prompts on the screen to select appropriate options. 1.9a Touch the language you want the thermostat to display, then touch Next. 1.9b Select Home or Business Next application, then touch Next. 1.9c Touch Next or name the thermostat location—touch THERMOSTAT and follow the rest of the instructions. Next 10 1.9d Select what your thermostat will control and touch Next. 1.9e Select your system type and touch Next The system type determines other selection for completing initial setup. Use the checklist from Step 1.6 when Next making selections. 1.9f Touch Next after making selections on each screen. 1.9g Touch Done on the last screen. The thermostat displays an option to connect to your Wi-Fi network. Next 11 2 Connect to your Wi-Fi network 2.1 Connect the Wi-Fi network After touching Done on the final screen of the initial set up (Step 1.9g), the thermostat displays an option to connect to your Wi-Fi network. Yes 2.1a Touch Yes to connect the thermostat to your Wi-Fi network. The screen displays the message “Searching for wireless networks. Please wait...” after which it displays a list of all Wi-Fi networks it can find. Note: If you cannot complete this step now, touch I’ll do it later. The thermostat will display the home screen. Complete this process by selecting MENU > Wi-Fi Setup. Continue with Step 2.1b. 12 2.1b Touch the name of the network you want to use. The thermostat Public displays a password page. Your Network 2.1c Using the keyboard, touch the characters that spell out your Neighbor home network password. 2.1d Touch Done. The thermostat displays “Connecting to your network. Please wait...” then shows a “Connection Successful” screen. Note: If your home network is not shown on the list, touch Rescan. 2.1e Touch Next to display the Done registration information screen. Next 13 Getting Help If you get stuck... At any point in the Wi-Fi connection process, restart the thermostat by removing the thermostat from the wallplate, wait for 5 seconds, and snap it back into place. From the home screen, touch MENU > Wi-Fi Setup > Choose a Network. Continue with Step 2.1b. Need more help? Find additional information in the User Guide. This thermostat works with common 24 volt systems such as forced air, hydronic, heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas fireplace, or with 120/240 volt systems such as baseboard electric heat. MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www.thermostat-recycle.org or 1-800-238-8192 for information on how and where to properly and safely dispose of your old thermostat. NOTICE: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C). 14 3 Register online for remote access To register your thermostat, follow the instructions on Step 3.1. Note: The Register Online screen remains active until you complete registration and/or touch Done. Note: If you touch Done before you register Done online, your home screen displays an orange alert button telling you to register. Touching that button displays registration information and an option to snooze the Register task. online for remote access Press for info 15 To view and set your Wi-Fi thermostat remotely, you must have a Total Connect Comfort account. Follow the instructions below. View the Wi-Fi Thermostat Registration video at wifithermostat.com/videos 3.1 Open the Total Connect Comfort web site Go to www.mytotalconnectcomfort.com M31570 M31570 16 3.2 Login or create an account If you have an account, click Login – or – click Create An Account. 3.2a Follow the instructions on the screen. 3.2b Check your email for a response from My Total Connect Comfort. This may take several minutes. Note: If you do not receive a response, check your junk mailbox or use an alternate e-mail address. 3.2c Follow activation instructions in the email. 3.2d Log in. 17 3.3 Register your Wi-Fi thermostat Thermostat ID Card Use the MAC ID and CRC ID to register After you are logged in to your Total this product at mytotalconnectcomfort.com HONEYWELL MODEL: MAC ID: MAC CRC: Connect Comfort account, register your Carte d’identification de thermostat Utilisez l’identification MAC et l’identification CRC pour thermostat. enregistrer ce produit à mytotalconnectcomfort.com Tarjeta de identificación del termostato 3.3a Follow the instructions on the Utilice la identificación MAC y la identificación CRC para inscribir este producto en mytotalconnectcomfort.com screen. After adding your ® U.S. Registered Trademark. © 2012 Honeywell International Inc. 69-2723EFS—01 M.S. 04-12 thermostat location you must enter Printed in U.S.A. 69-2723EFS-01 your thermostat’s unique identifiers: • MAC ID MAC ID MAC CRC • MAC CRC Note: These IDs are listed on the Thermostat ID Card included in the thermostat package. The IDs are not case sensitive. 3.3b Notice that when the thermostat is successfully registered, the Total Connect Comfort registration screen will display a SUCCESS message. You can now control your thermostat from anywhere through your laptop, tablet, or smartphone. 18 Getting started with voice For information on how to control your thermostat with voice, see the included “Talking with your Thermostat” card. Note that the voice commands for this thermostat are in English only. Need help? Visit wifithermostat.com or call 1-888-235-6569 for assistance before returning the thermostat to the store. Total Connect Comfort free app is available GET IT ON for Apple® iPhone®, iPad® and iPod touch® devices at iTunes® or at Google Play® for all Android™ devices. Download on iTunes 19 69-2791-03 Automation and Control Systems Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 wifithermostat.com ® U.S. Registered Trademark. Apple, iPhone, iPad, iPod touch and iTunes are trademarks of Apple Inc. All other trademarks are the property of their respective owners. © 2013 Honeywell International Inc. 69-2791—03 M.S. Rev. 07-13 Printed in U.S.A.

No comments:

Post a Comment

Popular Posts