Honeywell Thermostat TR70 User Manual - Honeywell Thermostat Manual Download

Latest

Sunday, April 5, 2020

Honeywell Thermostat TR70 User Manual

Zio®/Zio Plus LCD Wall Modules TR70, TR71, TR75 with Sylk® Bus OPERATING GUIDE begins with “Initial Power-Up” on page 2, and the general overview begins with “Operating the Zio Wall Module” on page 19. It is intended to guide you through the features and operation of the TR70 Series as you interface with the programmable controller and establish pre-programmed or custom configurations. LCD PANEL SOFTKEYS (3) UP/DOWN ARROW KEYS APPLICATION The Zio TR70 Series (TR70, TR70-H, TR71, TR71-H, TR75, NETWORK BUS PORT (ON BOTTOM OF CASE) and TR75-H OS numbers) LCD Wall Modules provide an M27344 operator interface for monitoring and adjusting parameters in the wall module itself and in the programmable controller Fig. 1. LCD Wall Module features. (refer to the Honeywell Spyder® User’s Guide, form 63-2662, or the ComfortPoint™ Programmable Controller User’s Guide, Contents form 63-2663, depending on the programmable controller Application ........................................................................ 1 used) to which it is wired. The wall module may be customized Preface ............................................................................. 1 and supports both a contractor and a tenant user interface. TR70 Series Features ....................................................... 2 Compatibility ............................................................. 2 NOTE: This document illustrates the wall module configura- Initial Power-Up ................................................................. 2 tion process using information from the Honeywell Setup and Configuration ................................................... 3 Spyder User’s Guide (form 63-2662). Initial Setup and Configuration .................................. 3 The wall module has a snap in mounting to a subbase that Selecting the Wall Module ......................................... 3 may be mounted on a wall, on a standard utility conduit box, or TR71/TR75 Labels .................................................... 3 on a 60 mm wall outlet box. Wiring connections to the wall Navigation and Memory Usage ................................. 3 module are made through a cutout in the back of the wall Wall Module Configuration ........................................ 4 module. General Settings ................................................... 5 Categories and Parameters .................................. 5 All models have a space temperature sensor, network bus Home Screen Options ........................................... 9 jack, and an LCD panel with three softkeys and two Up/Down Occupancy and Override ...................................... 10 adjustment keys. Models with -H also include an onboard Fan Command ....................................................... 12 humidity sensor. System Status and Command .............................. 13 Schedule/Time ...................................................... 14 Password ............................................................... 15 PREFACE Preview .................................................................. 16 This Operating Guide is intended to provide configuration Completing the Setup and Configuration .................. 17 information (using the Niagara Workbench tool) and a general Operating the Zio Wall Module ......................................... 19 overview of the TR70 Series operator interface. Configuration Contractor Mode Operation ...................................... 19 Tenant Mode Operation ............................................ 22 63-2719-03 ZIO®/ZIO PLUS LCD WALL MODULES Likewise, a TR71 can be replaced by another TR71 or TR75 TR70 SERIES FEATURES without reprogramming required. A TR75 can only be replaced with a TR75 where no reprogramming is desired. Table 1. TR70 Series Features. INITIAL POWER-UP Zio Zio Zio Plus Features TR70 TR71 TR75 IMPORTANT Scheduling x 1. Make sure the TR70 Series wall module is properly Parameter Memory (bytes) 1K 2K 4.9K mounted and properly wired and connected to the programmable controller. Up to four Zios on Sylk x* x x 2. Refer to the Zio™ LCD Wall Modules TR70 Series Enumerated Values x x with Sylk™ Bus – Installation Instructions, form 62- 0271, for specific installation requirements. Setpoint Limits as NVs – linking xx now possible Upon initial power-up before configuring the wall module, the System and Fan command as NVs x x LCD screen displays the phrase “PLEASE LOAd” in the Label/ Password protection x x Value area of Fig. 2. This phrase alternates with any onboard sensor display such as temperature. The TR71/TR75 also Firmware version/model visible on xx display the firmware revision number, model number and Sylk display bus address as shown in Fig. 27. 0.5 and 5 value increments x x Fig. 2 illustrates all the possible LCD Wall Module display "-" and "/" characters in parameter xx elements. Only those elements pertinent to the current names configuration and status actually display. * A maximum of four Zios may be wired on a single Sylk bus, with no more than one TR70 per bus. SYSTEM STATUS AREA LABEL/ VALUE Compatibility OVERRIDE (8 CHAR.) INFORMATION The TR70 Series LCD Wall Modules operate with the Sylk CURRENT ENGINEERING Enhanced Spyder Controller or the Sylk Enhanced DISPLAYED UNITS VALUE ComfortPoint Controller. The table below provides compatibility information for each model. The TR71/TR75 can FAN OCCUPANCY STATUS replace a TR70 in an installation where an upgrade to WEBs- INFORMATION SOFTKEY AX or Spyder or reprogramming is not desired. Features like LABELS scheduling, additional memory, etc. will not be available. M27353 Fig. 2. TR70 Series Wall Module - LCD screen. Table 2. Compatibility.* Scenari Spyde Spyder Compatible o r Tool Firmware ? Zio TR70/TR71/TR75* What can be done? 1 5.200 Latest YES New TR71/75 functionality Ideal scenario + available (if TR70 is present, then only TR70 functionality) 2 5.200 Old YES Only with TR70 functionality Spyder firmware can be upgraded (this becomes scenario + (TR71/75 can be used, but 1) only TR70 functionality will be there) 3 < 5.18 Latest NO Tool does not recognize the Spyder Tool can be upgraded (this becomes scenario 1) new Spyder Spyder firmware can be downgraded (this becomes scenario 4) 4 < 5.18 Old YES Only with TR70 functionality Both Spyder firmware and Tool can be upgraded (this (TR71/75 can be used, but becomes scenario 1) only TR70 functionality will Spyder Tool can be upgraded (this becomes scenario 2) be there) Spyder firmware can be upgraded (this becomes scenario 3) * The new Spyder tool (6.0 or greater) assumes the latest Spyder capability. At download, the Tool reads the brand/model of the connected Spyder and determines if it matches the features on the wire sheet. If old or new Spyder is programmed with aTR70, it can be physically replaced with a TR71 or TR75. 63-2719—03 2 ZIO®/ZIO PLUS LCD WALL MODULES SETUP AND CONFIGURATION TR71/TR75 Labels The TR71/TR75 allows the use of the following special Initial Setup and Configuration characters in label fields such as Categories and Parameter Names: underscore ( _ ) to insert a space, hyphen ( - ), and Once the wall module is wired to the controller, you configure forward slash ( / ). The TR70 allows use of the underscore the wall module using the PC-based, Niagara Workbench ( _ ) character to insert a space. Tool. Refer to the applicable programmable controller User’s Guide. (Refer to the Honeywell Spyder User’s Guide, form 63- 2662, or the ComfortPoint Programmable Controller User’s Navigation and Memory Usage Guide, form 63-2663, depending on the programmable The Honeywell Spyder Tool uses an intuitive, window-based controller used.) This tool is used to configure the wall module interface. A Help button on each screen provides assistance for either the Spyder or the ComfortPoint programmable with any entry or process. controller. IMPORTANT Confirm Bus Address Setting Use the Help button to display context specific help Check to ensure that the Wall Module’s bus address dial for the current window or pane display. See the lower (located on the back of the module) is set to match the setting left corner of Fig. 6 on page 5 for the location of the in the configuration tool. TR70 models can be set from 1–5 Help button. and TR71/TR75 can be set from 1–10 (0 on the Zio address NOTE: At any time, clicking the Preview button (lower left of dial is equal to 10 in the configuration tool). The address must main window, see Fig. 6 on page 5) displays the be different for each device on the Sylk bus. Up to four Zios updated wall module LCD as a pop-up. Preview sim- per Spyder are allowed with any combination of TR71/TR75s ulates the actual wall module interface and allows and up to three Zios are allowed if one or more is a TR70 you to verify the operation of the current configura- model. tion of the wall module. See “Preview” on page 16. Selecting the Wall Module Navigation You will use the Sylk S-Bus wall module function block from Table 3 describes the navigation buttons at the bottom of the the Palette’s Built-In folder (see Fig. 3). This configuration has wall module window. See the bottom of Fig. 7 on page 5 for nothing programmed except the room temperature parameter the location of these buttons. Buttons are greyed when and occupancy status. unavailable. 1. Add the Sylk S-Bus Wall Module function block to the wire sheet via a left click, drag, and drop. See callout 1 Table 3. Navigation Buttons. in Fig. 3. 2. Right click on the S-Bus Wall Module function block to Item Function/Use open the Configuration Properties menu. See callout 2 Help When clicked, this button provides context sensitive in Fig. 3. help for the currently selected item or parameter. 3. Left click on the title, Configuration Properties. This Preview When clicked, this button displays the updated wall action starts the Configuration Wizard. The Configura- module LCD in a pop-up window pane. Preview is tion Wizard steps (see Fig. 5 on page 4) are used to fully interactive and simulates the actual wall configure the wall module. module interface as currently configured (see “Preview” on page 16 for details). Save to For new custom configurations and standard Library configurations. Clicking the button opens the Save to Library screen (shown in Fig. 25 on page 17). This action RIGHT CLICK allows you to save the entire current wall module 2 configuration. The Save to Library button is disabled until you change the configuration (application). After a 1 change is made, you can save the new DRAG configuration into the library under a new name. SBusWallModule AND DROP Back Takes you backward one step in the wizard interface. VAV_Temp_NoBal_NwOvrdTime Next Takes you forward one step in the wizard interface. VAV_Temp_MnMxBal_NwOvrdTime VAV_Temp_KfacBal_NwOvrdTime VAV_Temp_NoBal_AllOverride Finish Clicking this button commits all changes to the database, closes the Configuration Wizard, and returns you to the wire sheet. M27820 Cancel Prompts you with a confirmation message. Fig. 3. Niagara Tool Interface - S-Bus wall module selection. If you reply Yes, then all selections/entries made since the Save to Library button or Finish button was last pressed are ignored, and the wizard interface quits. 3 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES SAVE BUTTON A SAVE button is available on screens that allow entries or selections. It is enabled whenever any change is made on the screen, and allows you to save your selections/entries at any time. See the ROOMSP Details area of the Categories and Parameters window in Fig. 12 on page 7 for an example of the SAVE button. Save is enabled whenever a change is made to the current page. When you press the SAVE button, the preview screen displays and your changes are reflected in the preview. If you try to leave the current screen without saving (click another icon or press the Back or Next button) and have made changes, a warning message appears. Memory Usage The wall module has a fixed amount of memory available for configuration data. The TR70 has 1,020 bytes of memory, the TR71 has 2,000 bytes of memory, and the TR75 has 4,950 bytes of memory. To view the current memory use information click on the Memory Usage Details button. A new window Fig. 4. Memory Usage Details screen. opens and displays a bar graph indicating the percentage of current memory used in each memory category. Wall Module Configuration Each of the memory categories should be below 100%. See To begin configuring the wall module: Fig. 4 on page 4. 1. Right click on the configuration’s function block to open NOTE: For a single Zio memory usage must be equal to or the Configuration Properties menu. less than 100% in order to download the configura- 2. Left click on Configure Properties. The Configuration tion to the programmable controller. If using multiple Wizard opens. The Configuration Wizard steps (see Fig. Zios, you should also check the Spyder Resource 5) are used to configure the wall module. usage. Total Zio memory use is limited to 5K bytes on Spyder. View the online help in the WEBs-AX Workbench to see See “General Settings”. troubleshooting tips for reducing memory usage in the TR70 Series if memory use is above 100%. See page 5. The following warning message displays when the memory See page 9. usage is greater than 100%: “Warning: Memory Limit Exceeded. The current wall See page 10. module configuration requires more memory than the wall module model can support. You will need to change the See page 12. configuration so that the memory usage is 100% or less before pressing the FINISH button.” See page 13. See page 14. See page 15. See page 16. Fig. 5. Wall Module - Configuration Wizard window showing Menu selections only. 63-2719—03 4 ZIO®/ZIO PLUS LCD WALL MODULES General Settings Categories and Parameters Using Fig. 6 and Table 4 as a guide, configure the General Settings. An image of the selected model and its capabilities updates in the display at the bottom of the window. I Categories and Parameters selection from Wizard Menu The categories and parameters menu item allows you to create, edit, and delete categories and parameters. ADDING A CATEGORY Fig. 7 shows the categories listed in tree format in the main window where you can add, edit, or remove them. In the bottom pane, Category Preview (at the bottom of Fig. 7) Fig. 6. General Settings screen. shows the current selected item. Clicking the Add Category button displays a details pane Table 4. General Settings. below the category and parameter tree as shown in Fig. 8. Item Function/Use NOTE: You can use the Remove button to delete unused categories and parameters to free up memory Block Name The wizard displays S-Bus Wall Module. space. Wall Module Select the appropriate type (Temperature Type Only, or a combination of Temperature, and/or Humidity) from the drop down list. Model Options Click LCD Display. Select Model Select the appropriate model, TR70, TR71, or TR75, from the drop down list. Wall Module Select a unique address for each TR70 Address Series devices connected to the Spyder. TR70 can be set from 1-5 and TR71/ TR75s can be set from 1-10. The address selected must match the address setting at the wall module (using the rotary switches). If setting the TR71/ TR75 rotary switch to 0, set the address to 10 in the configuration tool. Time Display Select 12 or 24 hour format. Format If you are creating a customized configuration or modifying a pre-programmed configuration, continue with “Categories and Parameters” on page 5. If you are using a pre-programmed configuration as is, Fig. 7. Category Preview. continue with “Preview” on page 17. CATEGORY DETAILS When you select a category from the Categories tree list and click the Edit button, a details pane displays for that category (see Fig. 8 on page 6). Here you can enter a category name and description. The number of parameters in this category are shown. The description text you enter is loaded to the controller but cannot be seen in the preview. 5 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES Here you can select Viewable by Tenant and Editable by Tenant. As an example, Fig. 10 shows the Details for the ROOMTEMP parameter. Here you would enter the description, select the parameter type from its drop-down list, enter the decimal accuracy, default sensor offset value, temperature units, and select the desired Home screen labels for the wall module. Fig. 8. Adding a Category. ADDING A PARAMETER Fig. 9 shows the categories and parameters listed in tree format in the main window. The parameters are listed under each category. Click on the box next to the category item to expand that item in the tree. You can add, edit, or remove Fig. 10. Adding a Parameter. parameters under each category. In the bottom pane, Category Preview (at the bottom of Fig. 9) shows the current CUT/COPY/DELETE CATEGORIES AND PARAMETERS selected item. A right-click accessible context menu allows you to cut, copy, paste, and delete parameters across categories. See Fig. 11. Clicking the Add Parameter button displays a details pane below the category and parameter tree as shown in Fig. 10. You can also drag/drop parameters in the tree and the result is a copy/paste per standard Niagara behavior. NOTE: You can use the Remove button to delete unused categories and parameters to free up memory You can also click (highlight) any item in the tree and then click space. the Remove button to delete any selected parameter or its category. Fig. 9. Parameter Preview. Fig. 11. Cut/Copy/Delete Categories and Parameters. PARAMETER DETAILS When you select a parameter from the tree list and click the Edit button, a details pane displays for that parameter. 63-2719—03 6 ZIO®/ZIO PLUS LCD WALL MODULES PARAMETER TYPES AND LIMITS See Fig. 12 for an illustration of the Parameter Type drop Table 5. TR70 Series Parameter Capacity Guidelines.* down list. There is a limit to the number of parameters that can be configured. In addition to the parameter limit, there is also a Parameter Type TR70 TR71 TR75 memory limit (see “Memory Usage” on page 4). Controller Value 30 95 250 Value From Wall Module 20 50 180 Network Setpoints 10 50 125 * The TR71/TR75 may vary from these capacity numbers depending on label names, parameter limit reuse, and other devices that Zio interacts with on the Sylk bus. NOTE: Network Variables need to be linked to the appropri- ate S-Bus wall module’s function block slots. See “Link Slots on the Wire Sheet” on page 18 for details. PARAMETER OPTIONS The TR71 and TR75 support additional parameter control. See Table 1 on page 2 for details. ENUMERATED VALUES Meaningful enumerated values can be displayed using the Enumerated option. From the Add/Edit parameter window check the Enumerated box and click on the Define Enum Range as shown in Fig. 13. Fig. 12. Parameter Type selection. The individual parameters are defined as: — Controller Value • These are read-only inputs to the wall module from the controller and include system status and occupancy status, if configured. Controller Value parameters take up less memory than other parameters. — Value From Wall Module • These are outputs from the wall module such as room setpoint. — Network Setpoints • A network setpoint is a network variable from the controller that you want to view and change at the wall module. — Sensors • 2 sensors (Temperature and Humidity) • 2 Sensor Offset Values (temperature and humidity) See Table 5 for the individual parameter maximums. Fig. 13. Click on the Enumerated Checkbox, then the Define IMPORTANT Enum Range button. You can not maximize all of these parameters together. The size of the data files limits the total Once in the Zio Enum Library dialog box (Fig. 14), click on the number. See the memory usage tool by clicking on dropdown to see pre-defined facets or define your own. For the Memory Usage Details button in the left pane of more detailed information see the online help in the the Configuration Wizard. Configuration Wizard. 7 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES as the low limit and the occupied cooling setpoint parameter as the high limit. To assign a setpoint to another setpoint's high or low limit, click on the Browse button next to the Low Limit or High Limit field. From the Select Parameter dialog box you can select the appropriate setpoint. This feature is an alternative to assigning a numeric value in the High/Low Limit fields, which require any change be made in the configuration tool and then loaded to Spyder. Continue with “Home Screen Options” on page 9. Fig. 14. Select from the existing library or define enumerated values. HIGH/LOW LIMIT PARAMETER LINKING This option allows for changes to a setpoint's high or low limit directly at a Zio by linking the high and low limit to a related setpoint. For example, for an occupied heat parameter, you could assign the related unoccupied heat setpoint parameter 63-2719—03 8 ZIO®/ZIO PLUS LCD WALL MODULES Home Screen Options • When selecting a parameter to display on the Home screen, note the maximum number of digits allowed, which varies from 3 to 4 depending on where the parameter displays on the LCD. • Click on the desired label box above each parameter to choose that label text to display on the wall module. I Home Screen Options • When you complete your Home screen selections, click the selection from Wizard Menu Save button on the lower left of the Details pane. After you choose the settings, use the Preview at the bottom left of the wizard window to exercise the Home screen and cycle through its options. Fig. 15, shows the Home Screen Options window and lists the Home screens currently configured, where you can add, edit, or remove them. DEFAULT HOME SCREEN The current default Home screen always displays at the top of the list. You can select any item in the list and click the Set As Default button to change the default Home screen. NOTE: You can use the Remove button to delete unused Home screen options to free up memory space. PREVIEW The bottom pane, Home Screen Option Preview, displays the current selected item’s Home screen. When more than one Home screen is configured, you can click the softkey button Fig. 15. Home Screen Options. rectangle, below “Next” in the preview pane, to cycle through all the Home screens in the list. ADD OR CHANGE HOME SCREENS Clicking the Add or Edit button displays the Details pane below the Home screen options tree (see Fig. 16). You use the Details pane to create or change a Home screen: •The Option Name item allows you to enter a 1 to 32 character description that displays in the Home Screen Options Available list. •The Set as Default selection, if clicked, causes this Home screen to be the initial Home screen for the wall module (after the configuration is downloaded to the wall module). •The Description text you enter allows more information to be entered on the home screen and will be loaded to the controller but cannot be previewed. •Use the Option Type selection to choose either single or multiple (1 to 3) parameters to display on the Home screen. • For the Single Parameter option type, there is an option to display a custom label up to 8 characters in length. • In the lower right of the window, you select the desired Home screen labels for the wall module. The number of parameters allowed (1-3) is based on your Option Type Fig. 16. Home Screen Details. selection. If you are finished with your configuration, go to “Preview” on page 16, otherwise continue with “Occupancy and Override” on page 10. 9 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES Occupancy and Override advanced settings. Clicking the Show Advanced Settings button displays the advanced settings. NOTES: 1. The preview at the bottom of the window displays the occupancy option currently selected. 2. If an Override option is selected, the Override softkey displays in the preview. Pressing the Over- ride softkey cycles through the available override I Ocupancy and Override options. selection from Wizard Menu ENABLE OCCUPANCY OVERRIDE Clicking the Enable Occupancy Override box enables this feature and also enables the current Occupancy status (3:00 hours as shown in Fig. 17). Clicking on the Settings button for the Valid States That You Fig. 17 shows the Occupancy and Can Override section opens the Override to Occupied Override options in the main Settings dialog box where you can configure values to any window for standard and desired number from 0 to 255. To conserve Zio memory, choose the same Override Type and Timed Override Details for Occupied, Unoccupied and Standby. STANDARD SETTINGS ADVANCED SETTINGS Fig. 17. Occupancy and Override screens. OCCUPANCY STATUS DISPLAY OPTIONS • Show occupancy override status – LCD shows the Here you select how the override status displays on the LCD. occupancy override status initiated from the LCD, The options are: independent of the programmable controller configuration. • Show effective occupancy status – LCD shows the actual • Do not show occupancy or override status – LCD does not occupancy status taking into account the programmable show occupancy or override, regardless of what the user controller configuration. initiates and the programmable controller configuration. 63-2719—03 10 ZIO®/ZIO PLUS LCD WALL MODULES OVERRIDE SETTINGS Clicking the Settings button displays the Override to Occupancy settings pop-up (see Fig. 18), where you can select Continuous (default) or Timed (hours or days) Override settings. TIMED OVERRIDE IN HOURS TIMED OVERRIDE IN DAYS Fig. 18. Override to Occupied Settings (Hours or Days). Clicking the Timed Override in Hours/Days boxes enable the The Override to Unoccupied selection’s Settings button Override details where you can enter the desired override displays pop-ups similar to the Override to Occupied Settings timings. shown in Fig. 18, but the timings apply to Unoccupied status. Clicking the Use Network Bypass Time Only box disables all NOTE: The Override to Unoccupied Settings does not have other override details. The timed override details will be a Network Bypass option. determined by the programmable controller configuration. This option only applies to Occupancy override settings. If you are finished with your configuration, go to “Preview” on Unoccupied and Standby do not use bypass. page 16, otherwise continue with “Fan Command” on page 12. ADVANCED SETTINGS When the Show Advanced Settings button is clicked, overrides to Occupied, Unoccupied, and Standby options are possible. 11 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES Fan Command Fig. 19, shows the Fan Command options in the main window for standard and advanced settings. Clicking the Show Advanced Settings button displays the advanced settings. I Fan Command selection from Wizard Menu STANDARD SETTINGS ADVANCED SETTINGS Fig. 19. Fan Command screens. Clicking the Enable Fan Command box enables the fan state value selections. Table 6. Fan State Values. The TR71/TR75 has the Set as Network Setpoint checkbox Selectable allowing the fan command to be configured as a network Fan State Fan State Values setpoint. This option is not available on the TR70. 2 State On / Auto The default Fan Command option is: 2 State (On / Auto). The 3 state On / Off / Auto default for the Fan State is selectable if Zio is commanding the 5 State Off / Auto / Low / Medium / High fan. If the fan commend is a network setpoint, then the default • Low, medium, and high are the three states of value is set on the controller's network setpoint. The Fan the fan speed indicator triangle. See Fig. 29 command value cannot be changed from Zio in the Contractor on page 19 for an example. mode. After you choose the setting, use the Fan Command Preview at the bottom of the window to exercise the Fan softkey to cycle through the options. If the Set as Network Setpoint box is checked for the TR71/TR75, the Preview screen will not emulate Zio's device behavior. If you are finished with your configuration, go to “Preview” on page 16, otherwise continue with “System Status and Command” on page 13. 63-2719—03 12 ZIO®/ZIO PLUS LCD WALL MODULES System Status and Command Fig. 20 shows the System Status and Command options in the main window. Clicking the Show Advanced Settings button displays the advanced settings. I System Status and Command selection from Wizard Menu STANDARD SETTINGS ADVANCED SETTINGS Fig. 20. System Status and Command screen. Clicking the Show System Status box enables the System Status line including the snowflake (cool) and flame (heat) Table 7. System State Values. icons and the System softkey on the LCD as shown in the Selectable System States Preview area at the bottom of the screen. Off / Heat (Heat Only) The System softkey on the LCD is enabled only when the Off / Cool (Cool Only) Enable System Command option is selected. Off / Heat / Cool (No Auto Changeover) The Enable System Command selections control the values Off / Auto / Heat / Cool (Auto Changeover) that display on the System Status line at the top of the wall module’s LCD screen. Off / Auto / Heat / Cool / Emergency Heat (Heat Pump) For TR71/TR75s click on the System Command checkbox to After you choose the setting, use the Preview button at the allow the System Command to be configured as a network bottom of the window to verify your configuration. If the Set as setpoint. Network Setpoint box is checked for the TR71/TR75, the Preview screen will not emulate Zio's device behavior. The default System Command option is: Off / Heat (Heat Only). The System commands are selectable. The System If you are finished with your configuration, go to “Preview” on command value cannot be changed from Zio in the Contractor page 16, otherwise continue with “Schedule/Time” on mode. page 14. 13 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES Schedule/Time I Schedule/Time Options selection from Wizard Menu Fig. 21. Schedule/Time for TR75. Fig. 22. Schedule/Time for TR70/TR71 is not supported so all options are grayed out. As shown in Fig. 21, the TR75 can provide access to the You also have the ability to configure how the Spyder schedule Spyder Schedule. This option is not available for use with the will display at the TR75: 8 day schedule, 7 day schedule, 5-2-1 TR70/TR71 as shown in Fig. 22. day schedule, or the 5-2 schedule. If using the 5-2-1 or 5-2 day schedule, you should configure the Spyder for the same The Schedule/Time options allow for if and how the Spyder schedule. schedule and Spyder time clock is accessed from Zio, whether or not the tenant can view or edit, etc. We recommend setting NOTE: If multiple Zios are used, we recommended using the the time in Spyder before configuring the Schedule/Time in same schedule display option for all Zios. the configuration tool. If you are finished with your configuration, go to “Preview” on NOTE: Setting an invalid time at Zio will cause Spyder to set page 16, otherwise continue with “Password” on page 15. the time to invalid. 63-2719—03 14 ZIO®/ZIO PLUS LCD WALL MODULES Password I Password Option selection from Wizard Menu Fig. 23. Assign Password for TR71/TR75 As shown in Fig. 23, the TR71/TR75 can be configured with a password that limits access to contractor level system changes from the TR71/TR75. The password option is not available for the TR70. The password can be assigned an eight character label that is displayed at the TR71/TR75 and a four digit password from 0000 to 9999. All TR71/TR75s on a Spyder can have the same or unique passwords. If the password option is enabled and the password is forgotten, it can be retrieved through the WEBs-AX Workbench in the Configuration Wizard. Go to “Preview” on page 16. 15 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES Preview Fig. 24 shows your current configuration of the wall module Home screen. You can select either the Tenant or Contractor view. The three softkeys in the preview LCD display are interactive and function just like the ones on the physical wall module display. I Preview selection from Wizard Menu Preview is a great way to verify all your configuration and setup parameters to ensure that they work exactly the way you want them to function. Preview simulates the actual wall module interface and allows you to verify the operation of the current configuration of the wall module. Clicking on the three softkey rectangles below the labels of the preview display exercises the features you have configured. Fig. 24. Preview screen. NOTE: Since the up and down arrow keys do not display in To complete the configuration, continue with “Completing the Preview mode, no adjustments to parameters (e.g Setup and Configuration” on page 17. setpoint temperature) can be made. 63-2719—03 16 ZIO®/ZIO PLUS LCD WALL MODULES Completing the Setup and All Configurations Configuration To complete the configuration process, perform the following sections in this order: For custom configurations, begin with “Custom Configurations 1. “Preview” Only”, otherwise continue with “All Configurations”. 2. “Confirm Memory Usage is within Limits” 3. “Finish the Configuration” Custom Configurations Only 4. “Link Slots on the Wire Sheet” on page 18 If you are customizing a configuration, use the Save to Library button to save your configuration. Clicking the button displays Preview a pop-up window as illustrated in Fig. 25. Use the Preview button or Preview menu selection to see how the wall module LCD screen will operate for your selected configuration (see “Preview” on page 16). Confirm Memory Usage is within Limits To view the current memory use information click on the Memory Usage Details button. A new window opens and displays a a bar graph indicating the percentage of current memory used in each memory category. Each of the memory categories should be below 100%. You can also click on the Memory Usage button below the bar graph to quickly view the percent used by each of the memory categories in the last column of the table. See Fig. 4 on page 4 for an illustration. If necessary, go back and remove unneeded categories, parameters, or Home screens. If using multiple Zios on one Sylk bus, check Spyder Resource usage also. Finish the Configuration Fig. 25. Save to Library screen pop-up. Click the Finish button to commit all your changes to the database, close the Configuration Wizard, and return to the wire sheet. 17 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES Link Slots on the Wire Sheet When making links from existing blocks to the wall module function block input slots, there is no need to break the This section describes how parameters may be linked to the existing links from these existing blocks. The new tool allows wall module. Refer the user to the Spyder User Guide, form for multiple output connections. 63-2662, for more specific information on variables and wire sheet logic. When connecting to slots on function blocks which lie on different wire sheets, remember that you can save time by The S-Bus Wall Module function block can be dropped into using the Link Mark method, a standard Niagara Workbench existing applications to replace the Conventional Wall Module linking mechanism. block. You can see an example in Fig. 26. A maximum of four Zios may be wired on a single Sylk bus, with no more than one TR70 per bus. Fig. 26. Example of the S-Bus Wall Module block dropped into a Venom VAV application. 63-2719—03 18 ZIO®/ZIO PLUS LCD WALL MODULES OPERATING THE ZIO WALL Contractor Mode Operation MODULE Contractor mode allows advanced options (such as modifying configured parameters) using the softkeys. Contractor mode also allows for customizing the tenant’s view including setting There are two modes of operation: the tenant’s Home screen and controlling the tenant’s “View • Contractor mode provides features a contractor would use More” access, which can provide the tenant with a view of the such as selecting the Home screen, selecting parameters configured parameters. the tenant can view, and monitoring/modifying controller parameters, which includes balancing. • Tenant mode provides features a tenant would use such as Contractor Home Screen Softkeys changing the setpoint, fan speed or system mode, initiating override, or monitoring/modifying permitted controller parameters. See page 22 for information about Tenant Mode operation. Contractor Mode (Entering and Exiting) Contractor mode allows access to the Setup function of the wall module. To enter and exit the Setup function – Press the Up and Down arrow keys and the middle softkey all at the same time (see Fig. 1 on page 1 for key positions). The TR71/TR75 will display the revision and model before going to the next screen M27357 as shown in Fig. 27. Fig. 29. Typical Contractor LCD display. The three softkeys on the contractor Home screen (see Fig. 29) provide the following: SET HOME SCREEN allows the contractor to choose among multiple Home screen options for the tenant. The tenant’s Home screen choices are created by the Con- figuration Wizard and downloaded to the wall module. Each wall module may have different Home screen choices. The contractor, using the softkeys, may choose which Home screen should be used, and may configure the Tenant view to show a subset (or none) of the configured parameters. • When the contractor clicks the SET HOME Fig. 27. On power-up, screen displays revision and Zio model SCREEN softkey, The display changes as shown in number. Fig. 30, and the softkeys change to DONE, CANCEL, and NEXT. If the password option is enabled you will be prompted to • Clicking the NEXT softkey cycles through the enter a four digit password as shown in Fig. 28. Use the up/ configured Home screens (see “Home Screen down arrow keys to change the first number and use the Done Options” on page 9). and Next softkeys to navigate from one digit to the next. • Click the DONE softkey when the desired Home screen displays. • The CANCEL softkey exits the Home screen display without saving any changes. Fig. 28. Password entry screen. 19 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES • When clicked, the EDIT softkey drops you into the parameter list for the displayed category and displays the first parameter in that category (e.g. the HUMIDITY parameter in the SET PNTS category as shown in Fig. 32). • If the parameter has been configured as adjustable by the tool, the Up and Down arrow keys adjust the value of the parameter. • The NEXT softkey displays the next parameter or category. • Click the DONE softkey when finished. M27378 Fig. 30. Sample Contractor display showing Home screen setup. SET VIEW MORE allows the contractor to provide parameter access (view only or adjustable) to the tenant’s VIEW MORE softkey. • Clicking the VIEW MORE softkey displays the first configured parameter as shown Fig. 31, and the softkeys change to DONE, CANCEL, and NEXT. • The Up and Down arrow keys switch the parameter between YES and NO (view or no view in Tenant Mode). YES means that the tenant has access to the parameter in the View More screen. NO means the tenant does not have access to the parameter. • If NO is selected for all parameters, then the VIEW MORE softkey does not display in tenant mode. • The NEXT softkey moves to the next parameter. • Click the DONE softkey when finished. • The CANCEL softkey exits VIEW MORE without saving changes to that parameter. Fig. 31. Set View More parameter display. PARAMETERS allows the contractor to monitor and/or adjust parameters in the programmable controller. • Clicking the PARAMETERS softkey displays the first configured category as shown in Fig. 31, and Fig. 32. Parameter display showing editing sequence. the softkeys change to DONE, EDIT, and NEXT. 63-2719—03 20 ZIO®/ZIO PLUS LCD WALL MODULES Sample Contractor LCD Displays The contractor mode allows advanced options using the softkeys. Contractor mode also allows for customizing the Tenant view including setting the tenant’s Home screen and View More access. The LCD display may be customized for the contractor. This section includes three examples of the various contractor Home and Parameter screens that are configurable for the LCD Wall Module. Not all possible screens are illustrated here. There are many other configurable screens. Fig. 36. Sample Contractor parameter display for TR71/TR75 showing enumerated value displays with label instead of numeric value. NOTE: Any configured parameter may be displayed. Editing the Schedule or Time The Schedule option lets you modify the schedule and change Spyder's time. The desired scheduling option (8 day, 7 day, etc.) is setup in the Configuration Wizard (see “Wall Module M27357 Configuration” on page 4) and based on that selection, option screens vary. The example below shows the flow for viewing/ Fig. 33. Sample Contractor Home screen display with System editing a schedule. Use the Edit softkey to move to the next Status, Setpoint, Outside Temperature, screen and use the up/down arrows to change values. When and Room Temperature (predominant). editing an event, use the Next softkey to go between editing the time and changing the state (OCC/UNOCC/STANDBY). To remove a programmed event, use the up/down arrow keys to scroll the time to either 12:00 p.m. or 12:00 a.m. Just before reaching 12:00 the time will change to four dashes (- - - -). Press the Done softkey at this point to remove a programmed event. In the 5-2 or 5-2-1 schedule options: “5” means Monday - Friday and Monday's events are shown on the Zio. The “2” means Saturday and Sunday and Saturday's events are shown on the Zio. And “1” means holiday. When Monday is changed, the TR75 copies that event to Tuesday - Friday and sends the controller the change for Monday through Friday. M27358 The same occurs for Saturday and Sunday when a change is made to Saturday. When a Holiday is modified it is also sent to Fig. 34. Sample Contractor parameter display showing a user- the controller. created discharge air parameter value. M27359 Fig. 37. Schedule display for contractor. Fig. 35. Sample Contractor parameter display showing sensor setpoint value (CO2 sensor from controller). 21 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES TENANT HOME SCREEN SOFTKEYS As shown in Fig. 40, there can be three softkeys configured for the tenant’s Home screen – FAN, OVERRIDE, and SYSTEM & VIEW MORE. NOTES: 1. The Fan and Override settings are optional for Home screen setup. 2. If the System Command option is not enabled, then the SYSTEM softkey does not display on the tenant’s Home screen. 3. If there are no parameters configured for tenant access, the VIEW MORE softkey does not display on the tenant’s Home screen. Fig. 38. Select the day. FAN allows the tenant to adjust the fan settings depending on the fan options (2, 3, or 5 position) configured. As shown in Fig. 41, each click of the FAN softkey changes the fan icon display between: • 2 position: ON and AUTO • 3 position: OFF, AUTO, and ON • 5 position: OFF, AUTO, and the three states of the fan speed indicator (low, medium, and high) Fig. 39. Select the Event to edit the time and occupancy state. Tenant Mode Operation The tenant, using the softkeys and arrow keys, may change the setpoint, fan speed, system mode (heat/cool), or initiate override, if these features are configured. The tenant may change the Occupancy Override parameter to Occupied, Fig. 41. Fan display for Tenant showing 5-position setting with Unoccupied, or Standby. And, the override can be timed in fan at medium speed. minutes, days, or be continuous. OVERRIDE allows the tenant to override the Occupancy set- tings (see Fig. 42). • Depending on the occupancy/override configuration, each click of the OVERRIDE softkey changes the occupancy icon displays between STANDBY, OCCUPIED, and UNOCCUPIED. • If an override is set by the tenant, the OVERRIDE softkey changes to CANCEL OVERRIDE. • Clicking the CANCEL OVERRIDE softkey cancels the override. M27354 Fig. 40. Typical Tenant LCD display. 63-2719—03 22 ZIO®/ZIO PLUS LCD WALL MODULES NOTE: Home screens can display one to three of any of the following parameters: temperature setpoint, room temperature, room humidity, outdoor humidity, and outdoor temperature, and time, or one of virtually any parameter in the controller. SAMPLE TENANT HOME SCREEN DISPLAYS Figures Fig. 44 through Fig. 49 illustrate typical tenant home screens. Fig. 42. Override display for Tenant. SYSTEM & VIEW MORE Depending on the configuration, this softkey allows the tenant to change the system state and view/adjust configured parameters (see Fig. 43). • The first click displays the system information and the Up and Down arrow keys change the system state between OFF, AUTO, COOL, HEAT, and EM.HEAT (emergency heat). M27352 • Clicking the VIEW MORE/NEXT softkey displays each viewable parameter. Fig. 44. Sample Tenant Home screen with Room Temperature • If the contractor enables tenant access to a parameter, and Setpoint (predominant). then the tenant can use the Up and Down arrow keys to adjust the parameter’s value, otherwise the tenant is The Fan and Occupied settings are optional for Home screen able to only view the parameter and its value. setup. If there are no parameters configured for tenant access, the “View More” softkey does not display on the tenant’s NOTE: When the contractor configures a parameter and Home screen. selects the Editable by Tenant check box, this enables the tenant to adjust the parameter’s value. See Fig. 12 on page 7 for an example. • Click the CANCEL softkey to exit the display without saving changes to the parameter. • Click the DONE softkey when finished. M27354 Fig. 45. Sample Tenant Home screen with System Status, Setpoint, Outside Temperature, and Room Temperature (predominant). Fig. 43. System and View More display for Tenant. Tenant Home Screen Display The LCD display may be customized for the tenant. This section includes a few examples of the various tenant Home screens that are configurable for the LCD Wall Modules. Not all possible Home screens are illustrated here. There are many other configurable Home screens. M27355 Fig. 46. Sample Tenant Home screen with Humidity and Room Temperature (predominant). 23 63-2719—03 ZIO®/ZIO PLUS LCD WALL MODULES NOTE: In Fig. 48, the Home screen is configured with only a single, custom parameter. See “Preview” on page 9. M27379 Fig. 47. Sample Tenant Home screen with Room Temperature and Time (predominant). M27356 NOTE: In Fig. 47, there are no Fan, System, or View More Fig. 49. View More display showing CO2 sensor value from softkey options configured for this Home screen. controller. NOTE: As shown in Fig. 49, any configured parameter may be displayed to the tenant. M27498 Fig. 48. Sample Tenant Home screen with a single, custom parameter. Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North ® U.S. Registered Trademark Golden Valley, MN 55422 © 2012 Honeywell International Inc. 63-2719—03 S.B. 04-2012 customer.honeywell.com Printed in United States

No comments:

Post a Comment

Popular Posts